pma-series ? p6au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 p6au-xxxxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitors input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 3% short circuit protection short term line regulation 1.2% / 1% vin change load regulation (20% - 100%) 10% (3.3vout models: 20%) ripple and noise (20mhz bandwidth) 100 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 1000 vdc i/o isolation capacity 60 pf, typ. i/o isolation resistance 1000 mohm switching frequency 80 khz (variable) humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs physical specifications case material non conductive black plastic (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 1.5g, typ. environment specifications operating temperature -40 to +85c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection rohs conform soldering 260c, max. (1.5mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm a series p6au - xxxxelf is a family of cost effective 1 w single output dc/dc converters. these converters are in an ultra miniature sip4 case. devices are encapsulated. high performance fe atures: 1000vdc input/output isolation, high efficiency operation, output voltage accuracy of 3% maximum, input range of 10% tolerance and low output ripple and noise. pma-series 1 watt unregulated single output sip4 case 1 kv dc i/o isolation low ripple and noise rev.11-2008
pma-series ? p6au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # i n p u t v o l t a g e ( v d c ) i n p u t c u r r e n t n o l o a d ( m a ) i n p u t c u r r e n t f u l l l o a d ( m a ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output p6au-3r33r3elf 3.3 25 452 3.3 303 67 220 p6au-3r305elf 3.3 30 415 5 200 73 220 p6au-053r3elf 5 25 278 3.3 303 72 220 P6AU-0505ELF 5 25 267 5 200 75 220 p6au-057r2elf 5 25 264 7.2 138.8 76 220 p6au-0509elf 5 25 260 9 111.1 77 220 p6au-0512elf 5 25 257 12 83.3 78 220 p6au-0515elf 5 25 257 15 66.67 78 220 p6au-0518elf 5 25 257 18 55.5 78 220 p6au-0524elf 5 25 257 24 41.67 78 220 p6au-123r3elf 12 16 116 3.3 303 72 220 p6au-1205elf 12 16 112 5 200 75 220 p6au-127r2elf 12 16 110 7.2 138.8 76 220 p6au-1209elf 12 16 109 9 111.1 77 220 p6au-1212elf 12 16 107 12 83.3 78 220 p6au-1215elf 12 16 107 15 66.67 78 220 p6au-1218elf 12 16 107 18 55.5 78 220 p6au-1224elf 12 16 107 24 41.67 78 220 p6au-243r3elf 24 10 58 3.3 303 72 220 p6au-2405elf 24 10 56 5 200 75 220 p6au-247r2elf 24 10 55 7.2 138.8 76 220 p6au-2409elf 24 10 55 9 111.1 77 220 p6au-2412elf 24 10 54 12 83.3 78 220 p6au-2415elf 24 10 54 15 66.67 78 220 p6au-2418elf 24 10 54 18 55.5 78 220 p6au-2424elf 24 10 54 24 41.67 78 220 p6au-483r3elf 48 7 29 3.3 303 72 220 p6au-4805elf 48 7 28 5 200 75 220 p6au-487r2elf 48 7 27 7.2 138.8 76 220 p6au-4809elf 48 7 27 9 111.1 76 220 p6au-4812elf 48 7 27 12 83.3 76 220 p6au-4815elf 48 7 27 15 66.67 76 220 p6au-4818elf 48 7 27 18 55.5 76 220 p6au-4824elf 48 7 27 24 41.67 76 220 if you need other specifications, please enquire.
pma-series ? p6au-xxxxelf ? single output ? sip4 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 package / pinning / derating modelcode datecode 1 2 3 4 11.68 (0.46) 9.65 (0.38) 3.05 (0.12) 2.54 (0.10) bottom view 1 2 3 4 1.25 (0.05) 0.50 (0.02) 6.00* (0.24)* 0.50 (0.02) 0.50 (0.02) 0.50 (0.02) 0.25 (0.01) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. * the thickness of 48vin voltage is 7.50 (0.29) pe a k sip4 C plastic case # single 1 - vin 2 +vin 3 - vout 4 +vout pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load. - operation under no-load conditions will not damag e these devices, but they will not observe the list ed specifications. - for reduce converter?s ripple & noise, it is reco mmended to add a 4.7 f~100 f capacitor in output end. for emi performance improvement, it is recommended to add a 12 h inductor and a 10 f~220 f capacitor in input end. emc specifications radiated emissions en 55022 fcc 47cfr part 15/b class b class b esd iec 61000-4-2 perf. criteria b rs iec 61000-4-3 perf. criteria a
|
